Presentation video of the RED SEA - ReefATO+ 3 in 1
The sensor of the ReefATO osmolator
Titanium level sensors and a temperature probe in a single block.
Heavy-duty water level sensor (one-piece EC technology), with built-in back-up sensors to stop the pump, located 2.5 cm above the normal stop level of the pump. The Reef-Spec titanium probe set gives a real-time indication of the water level on the sensor, which can be viewed at any time on the ReefBeat app. The temperature probe integrated into the ATO+ sensor has been pre -calibrated to achieve an accuracy of ±0.1°C.
The pump of the ReefATO osmolator
Silent pump with variable flow, diameter of 4.5cm, maximum height 2.5 meters.
Silent osmolator pump, variable flow, 12 vdc. Cylindrical design with a diameter of 4.5 cm to fit in standard jerry cans. Maximum flow 300 L/h, maximum head 2.5m, power 6-10W. The performance controller automatically stops the pump and notifies you via the ReefBeat app if it is not connected, if it jams or if the RO water supply has run dry. The pump flow is automatically adjusted according to your installation to maintain a flow rate of approximately 72 L/h ensuring a quiet and splash-free water flow in the settling.
ReefATO Leak Detector
High precision titanium leak sensor. You are notified on your smartphone in the event of a leak.
If a leak is detected, the automatic filling of the osmolator is immediately deactivated, and after a few seconds to confirm that the leak persists, the controller emits an audible alarm (configurable) and sends a notification to your mobile.
Pair the leak detector with ReefBeat's Quick Action Emergency Stop mode and the ReefBeat ecosystem will automatically shut down other connected equipment such as ReefRun return pumps.
ReefATO Controller
The controller allows the connection of all sensors and the pump. It provides the wifi connection to the ReefBeat.
Complete Installation Kit
• Sensor holder and magnetic corner support for glass up to 12mm
• Silicone tube 3m long and 1.5mm thick, Ø int 5mm
• Quiet flow – Hose holder, attaches to 4-12mm glass
Fleece-Roll500 from Red Sea is a roll of high flow 50gsm non-woven polyester filter fabric , for the ReefMat 500 filter . Compatible with skimmers. The roll has a length of 28 m and a width of 11.3 cm.
The Tunze DOC Skimmer 9410 DC is recommended for aquariums up to 1200 liters of seawater. DOC Skimmer 9410 DC has the same features as model 9410, but is equipped with Foamer electronic 9410.044 DC, a Controller and a mains power supply.
Aquafit 2 from Aqua Medic is universally usablefor any pendant luminaire with side screw assembly of the housing. Requirement: Sufficiently long screws in the corners of the housing (max. Ø 4 mm).
AF Vitality Coral V 10ml from Aquaforest is a concentrated vitamin supplement for corals . It reinforces the intensity of the colors and increases the resistance of the corals.
Care MagnetStrong 0220.020 is a powerful cleaning magnet for aquariums. Forwindows from 15 to 20 mm maximum , width 86 mm, length 140 mm, comprising a stainless steel blade and two spare plastic blades.
Two-sensor water level regulation, for placement in under-aquarium filtrations, Comline® filters or directly at the edge of the aquarium. Supplied complete with 12 V mains power supply, dosing pump, hoses and Magnet Holder for sensors.
SP 3000 Levelmat is an automated system for the compensation of evaporated water in freshwater or saltwater aquariums. It consists of the SP 3000 hose pump and a directly connected level switch. The contactor is fixed with its holder in the aquarium or the filter box at the height of the desired water level.
Single-sensor level control for nano-aquariums or small aquariums up to 200 liters , to be placed in under-aquarium filtrations or directly at the edge of the tank.
Supplied ready to use with 12 V mains power supply, very low voltage dosing pump, 3 m hose, Magnet Holder for panes up to 10 mm and sensor protection cover.
TUNZE RO Water Controller 8555 is an automatic top-up with regulation for TUNZE® RO reverse osmosis or all types of reverse osmosis with pure water tank. It consists of a controller, two sensors, a solenoid valve and a 12 V mains supply. To control a mains-powered device, the solenoid valve can be replaced by the socket ordered 3150.110.
Thanks to the Smart ASOV , no more flooding due to overflow of the reverse osmosis water tank. Smart ASOV stops the osmosis unit in time thanks to a sensor and will avoid any unpleasant surprises!
Level Keeper from Reef Factory is a device that helps maintain a constant level of water in the aquarium . This mini computer continuously monitors the water level of your aquarium. If the water evaporates, the system injects the corresponding amount of water back into the aquarium. This filling process is designed to work without a hitch, but if something goes wrong, you get an alert in the form of an SMS.
Auto Aqua 's Smart ATO Duo is a unique automatic osmolation system with two non-contact digital sensors that monitor and automate the refilling of evaporated water.
.jpg)
.jpg)
.png)
.jpg)
.jpg)
%20(1).png)
.jpg)
